Difference between revisions of "Raspberry Pi Image Install"
(→Flash the Image) |
(→Get the Image) |
||
Line 1: | Line 1: | ||
− | = | + | = Raspberry Pi 3 Image with ROS = |
− | * [http://www.german-robot.com/2016/05/26/raspberry-pi-sd-card-image/ Raspberry Pi SD-Card Image] | + | * [http://www.german-robot.com/2016/05/26/raspberry-pi-sd-card-image/ Raspberry Pi SD-Card Image Page] |
+ | * [http://www.german-robot.com/ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img.zip Image File] | ||
− | + | "Only Ubuntu and ROS installed, without the SW that is needed for the robot (zipped, min 32GB SD Card – as SD cards have different sizes a 64GB card is needed to be sure it works – otherwise 100-200MB might be missing." | |
− | Only Ubuntu and ROS installed, without the SW that is needed for the robot (zipped, min 32GB SD Card – as SD cards have different sizes a 64GB card is needed to be sure it works – otherwise 100-200MB might be missing | + | |
− | + | ||
− | + | * ROOT PASSWORD: raspberry | |
+ | * Ubuntu Mate Xenial 16.04 | ||
+ | * ROS Kinetic | ||
− | + | "Make sure to read the README.TXT on the desktop! Note: You should enter the following in terminal: “nano /home/ubuntu/.bashrc” then add following at the end of the file: “source /home/ubuntu/catkin_ws/devel/setup.bash” all without the “”. Then press ctrl+x to exit and save. | |
− | + | unzip 3.36GB ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img.zip | |
− | + | ||
+ | Yields: 32.0GM ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img | ||
= Flash the Image = | = Flash the Image = |
Revision as of 00:25, 25 February 2017
Raspberry Pi 3 Image with ROS
"Only Ubuntu and ROS installed, without the SW that is needed for the robot (zipped, min 32GB SD Card – as SD cards have different sizes a 64GB card is needed to be sure it works – otherwise 100-200MB might be missing."
- ROOT PASSWORD: raspberry
- Ubuntu Mate Xenial 16.04
- ROS Kinetic
"Make sure to read the README.TXT on the desktop! Note: You should enter the following in terminal: “nano /home/ubuntu/.bashrc” then add following at the end of the file: “source /home/ubuntu/catkin_ws/devel/setup.bash” all without the “”. Then press ctrl+x to exit and save.
unzip 3.36GB ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img.zip
Yields: 32.0GM ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img
Flash the Image
Determine that SDA disks are out there before the SD card has been inserted into the workstation. We don't want to mess it up.
ls /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda5
Determine that the SD card will be located at SDB.
ls /dev/sd* /dev/sda /dev/sda1 /dev/sda2 /dev/sda5 /dev/sdb /dev/sdb1
Flash the image to SDB. It takes about 45 minutes on my NUC with an STD.
sudo dd bs=4M if=ubuntu-mate-16.04-armhf-ROS-Kinetic-raspberry-pi.img of=/dev/sdb [sudo] password for eepp: 7635+1 records in 7635+1 records out 32026656768 bytes (32 GB) copied, 2714.49 s, 11.8 MB/s
Sync
sync